Tracked · Full Electric · RTK + LiDAR + Camera

WJ-E-1100 Autonomous Electric Flail Mower

TRACKED · 1.1 M FLAIL DECK · 22 kWh LiFePO4

A high-output, fully electric flail mower that works its routes on its own. RTK guidance with LiDAR and camera sensing keeps it on line and aware of obstacles, a 22 kWh CATL-cell pack covers long shifts, and an 800 m industrial remote stays on hand for manual backup — no exhaust, no fuel, no boundary wire.

1,100 mm
Cutting width
6,000 m²/h
Approx. output
510 kg
Net weight
WANJI WJ-E-1100 tracked fully-electric autonomous flail mower in an orchard

Autonomous coverage for large, overgrown sites

A 1.1 m flail deck, a 22 kWh electric drivetrain and RTK + LiDAR + camera autonomy in one tracked chassis. Rough cutting becomes a scheduled route, with the operator supervising instead of riding.

RTK

RTK + LiDAR + camera autonomy

RTK-guided routes without boundary wire, with LiDAR and camera sensing for obstacle awareness. Routes are set at commissioning, then repeated on schedule.

0

Zero-emission 22 kWh pack

A LiFePO4 traction pack built with CATL cells. No petrol, no exhaust and far less noise than a combustion flail mower.

1.1M

1.1 m flail deck, 5,000 W

22 rotor sets carrying 44 special-alloy steel flail blades on NSK high-speed bearings, rated at approximately 6,000 m²/h. Deck lift and engine start are remote-controlled.

7H

Up to 7 h per charge

Long shifts between charges, with a 3-year battery warranty: free replacement if capacity degrades to 70% within the warranty period.

TRK

Off-road tracked traction

Twin 1,500 W travel motors and wide high-tooth off-road tracks keep the deck working on soft, uneven ground where wheeled machines struggle.

800

800 m industrial backup remote

The industrial HotRC remote controller covers remote start, deck lift and manual driving at distances up to 800 m — backup for positioning, recovery and spot work.

Technical specification

Figures apply to the standard WJ-E-1100 configuration. Final configuration is confirmed per order.

PlatformTracked, fully electric, zero emission, RTK autonomous
ApplicationGrass, weeds and heavy ground cover on orchards, solar sites and rough terrain
NavigationRTK autonomous guidance with LiDAR + camera sensing; no boundary wire
Manual backupIndustrial HotRC remote controller, range up to 800 m
Cutting width1,100 mm
Cutting height150–180 mm, remote-controlled deck lift
Cutter-head motor5,000 W
Flail rotor22 rotor sets / 44 special-alloy steel flail blades
BearingsNSK high-speed bearings
Rated outputApprox. 6,000 m²/h
Traction batteryLiFePO4 pack with CATL cells, 22 kWh class
Working time per chargeUp to 7 hours
Travel motors2 × 1,500 W
Slope capabilityClimbs up to 60°; stable operation on 22° slopes
TracksWide high-tooth off-road tracks
Remote functionsRemote start and remote deck lift
Battery warranty3 years; free replacement if capacity degrades to 70% within the warranty period
Dimensions (L × W × H)193 × 121 × 70 cm
Net weight510 kg

Autonomous routes are set during commissioning; the 800 m remote controller is retained as manual backup rather than the primary operating mode. Cutting height adjusts from 150 to 180 mm, and the machine climbs slopes up to 60° (stable operation on 22° slopes). Final configuration is confirmed per order.

Typical sites

Orchards & vineyards Solar & wind farm ground cover Roadside & drainage corridors Rough pasture & paddocks Utility corridors & substations Reclaimed land & set-aside

The machine, up close and at work

Factory and field photos of the E-1100 platform. No pricing is published on this site.

WJ-E-1100 flail deck and tracked chassis seen from the front side
Flail deck and chassis. The 1,100 mm flail head with remote lift, mounted on the wide-track electric chassis.
WJ-E-1100 mowing between rows on an orchard site
Working between rows. The E-1100 cutting ground cover on an orchard site during field runs.

Frequently asked questions

Autonomy, battery and deck questions buyers raise before ordering.

Is the WJ-E-1100 autonomous or remote controlled?

It is an autonomous machine. RTK guidance works programmed routes without boundary wire, supported by LiDAR and camera sensing. The industrial HotRC remote controller, with a range of up to 800 m, is retained for positioning, recovery and manual spot work.

How long does it work on one charge?

Up to 7 hours from the 22 kWh class LiFePO4 pack with CATL cells. Actual runtime depends on vegetation density, terrain and working speed.

What output can I expect?

The rated output is approximately 6,000 m²/h with the 1,100 mm deck, driven by a 5,000 W cutter head and 22 rotor sets carrying 44 special-alloy steel flail blades on NSK high-speed bearings.

How is cutting height adjusted?

The deck lifts by remote control, so cutting height can be changed without stopping at the machine. The cutting-height range is 150–180 mm.

What is the battery warranty?

The battery carries a 3-year warranty: if capacity degrades to 70% within three years, the pack is replaced free of charge.

Fleet sizing and quotation

Tell us the area, the vegetation and the charging access on site. We will confirm the configuration, the expected coverage per charge and the fleet size, then issue a quotation for your destination.

Request a Quotation