The short answer: choose the deck width from your narrowest clear row corridor, the chassis from your steepest working slope, and the daily capacity at about 65% of the rated m²/h figure. On WANJI machines that usually means the wheeled WJ-R1 for flat, quiet blocks, the tracked WJ-T-900A / T-1100M / T-1300M for slopes from 40° to 60°, and the WJ-F-1000L flail where grass has turned into light brush. The rest of this guide is the working math behind those three decisions.
1. Start with the row corridor, not the catalogue
On a PV site the machine lives between posts, cable trays and panel edges. The number that limits you is not the average row spacing on the layout drawing — it is the narrowest clear corridor the mower has to pass, measured on the ground after installation. Walk a few rows and record the tightest points: end posts that were never aligned, a tray bracket that sits 80 mm lower than the others, a panel clamp that protrudes.
Then leave working clearance on both sides. As an example, if the clear corridor is 1.4 m, a 900 mm deck leaves 500 mm of total margin and will run unattended with far fewer interventions than a 1,300 mm deck that leaves only 100 mm. A wider deck is only faster if it passes the tightest row at full speed — otherwise you are buying interruptions.
WANJI cutting widths are 790 mm (WJ-R1), 900 mm (WJ-T-900A), 1,000 mm (WJ-F-1000L flail), 1,100 mm (WJ-T-1100M) and 1,300 mm (WJ-T-1300M). Sites with mixed row spacing are often best served by one narrower machine everywhere rather than a wide deck that only fits half the blocks.
2. Match the chassis to the steepest working slope
Solar sites are rarely as flat as the aerial photo suggests: access ramps, drainage swales and boundary banks are where mowing accidents happen. Rate the machine against the steepest place it will actually mow, not against the panel field average.
- Flat, maintained blocks, noise-sensitive neighbours: the wheeled fully-electric WJ-R1, 118 kg, zero-turn on the spot, automatic charging dock.
- Embankments and rougher ground up to 40°: the tracked hybrid WJ-T-900A, with up to 8 hours per full tank.
- Steep sites up to 60°: the tracked WJ-T-1100M and WJ-T-1300M on the shared wide-deck chassis.
- Tall growth with light branches: the tracked WJ-F-1000L flail, maximum working slope 45° and maximum climbing angle 55°.
The T-900A and the T-1100M/T-1300M are two different platforms, so deck geometry, cut-height range and service items are quoted per model — do not treat their specifications as interchangeable.
3. The working specifications
These are the figures to use when you size a machine for a solar block. Rated output is the manufacturer figure under suitable conditions, not a promise for overgrown, wet or obstructed rows.
| Model | Deck | Rated output | Working window | Max slope |
|---|---|---|---|---|
| WJ-R1 wheeled electric | 790 mm, 20–100 mm cut | 2,000 m²/h | ≈2 h / 4,000 m² per pack, auto-dock | Flat blocks |
| WJ-T-900A tracked hybrid | 900 mm, 20–150 mm cut | 3,000–4,000 m²/h | Up to 8 h per full tank | 40° |
| WJ-T-1100M tracked hybrid | 1,100 mm, 10–200 mm cut | 3,000–4,000 m²/h | 4–5 h, 9.9 L tank | 60° |
| WJ-T-1300M tracked hybrid | 1,300 mm, four blades | 4,500–5,500 m²/h | 6–7 h, 19.0 L tank | 60° |
| WJ-F-1000L tracked electric flail | 1,000 mm, 0–200 mm hydraulic lift | For tall grass & light brush | ≈8 h per charge, 30.24 kWh | 45° working |
4. How to calculate hectares per day
hectares per day = rated output (m²/h) × working hours × 0.65 ÷ 10,000
The 0.65 field-efficiency factor covers turning, obstacle slowdowns, repositioning between blocks and the strip you will still finish by hand.
Worked example: a WJ-T-1300M at a mid-range 5,000 m²/h over a 6.5-hour tank gives 5,000 × 6.5 × 0.65 ≈ 21,100 m², or about 2.1 hectares per full tank. Using the same 65% assumption across the range:
- WJ-T-900A: roughly 1.6–2.1 ha per full tank (3,000–4,000 m²/h, 8 h)
- WJ-T-1100M: roughly 0.9–1.2 ha per full tank (3,000–4,000 m²/h, 4–5 h)
- WJ-T-1300M: roughly 1.9–2.3 ha per full tank (4,500–5,500 m²/h, 6–7 h)
- WJ-R1: about 4,000 m² per battery pack as rated — with the auto-charging dock it resumes by itself, so daily coverage depends on how many charge cycles you let it run
For a 20-hectare site mowed ten times a season, that arithmetic tells you immediately whether one machine is enough or whether the block should be split between two. If a contractor currently needs a crew week for the same area, the comparison becomes a labor-hour question — our cost breakdown against manual mowing has the reusable formula.
5. Plan separately for tall growth and the close-in strip
Two parts of a solar site do not behave like the brochure. First, blocks that have been left for a season stop being mowing and become light brush cutting: that is flail work. The WJ-F-1000L uses a 4,000 W cutter head at up to 3,500 rpm with a hydraulic 0–200 mm deck lift, so it can travel with the deck raised and lower it per zone; its 72 V 420 Ah (30.24 kWh) pack gives about 8 hours per charge.
Second, the strip immediately around posts, cable trays and panel edges is close-in work on every site we know of, whatever the machine brand. Plan for a person with a trimmer on that strip and let the autonomous machine do the repetitive 90% between the rows. Buying a mower on the assumption that nobody will ever walk the site again is how projects disappoint.
6. Check RTK behaviour under your arrays before you sign
Between rows with open sky, RTK-GNSS holds a Fix and the mower tracks its planned lines at centimetre level. Under the panels and in terrain shadow, receivers on any brand can drop from Fix to Float — that is physics, not a defect. WANJI machines combine GNSS with IMU and LiDAR so the mower holds its row through short shading events, but row orientation, panel height and shading still deserve a proper look before purchase. The full explanation, including the acceptance criteria worth writing into a contract, is in our GNSS signal-loss article; the site-level picture is on the solar and wind vegetation management page.
Buyer checklist for a solar block
- Measure the narrowest clear corridor in each block, then pick the deck width that keeps clearance on both sides.
- Record the steepest actual mowing line — ramps, swales and boundary banks included — and choose wheeled or tracked from that, not from the field average.
- Run the hectare formula at 65% efficiency and decide whether one machine covers your seasonal passes or the site needs splitting.
- Separate first-pass brush cutting from maintenance mowing; overgrown blocks point to the flail, maintained blocks to the finishing decks.
- Walk the RTK and close-in questions before ordering: shading pattern, post and tray strip, and who finishes the edges.
Quick answers
How many hectares per day is realistic?
Rated output × hours × 0.65 ÷ 10,000. On that basis roughly 1.9–2.3 ha per full tank for a WJ-T-1300M, 1.6–2.1 ha for a WJ-T-900A and 0.9–1.2 ha for a WJ-T-1100M.
Is the widest deck always the fastest?
No. If it only fits the easy rows, you lose the time again in interventions and manual follow-up. Size to the tightest corridor.
Can one machine handle both brush and finishing?
They are different deck types. Sites with seasonal overgrowth usually run a flail pass first, then maintain with a finishing deck.
Do you publish prices for a solar setup?
No list prices. We quote per model, quantity, configuration and destination — see the Buyer FAQ, then send your block measurements.
